Axles, Shafts, Joints and Couplings

Made in ItalyThis Boot fits on the outside of the Drive Shaft where it connects to the WheelIt is basically a rubber dust cover and fits onto the Drive Shaft and around the lip of the FlangeDiameter:  19mm (smaller type shaft)(These are designed to be nice tight fit so they..

Made in ItalyThis Boot fits on the outside of the Drive Shaft where it connects to the WheelIt is basically a rubber dust cover and fits onto the Drive Shaft and around the lip of the FlangeDiameter:  22-24mm (larger type shaft)(These are designed to be nice tight fit so they ma..

These Washers are located at the end of the Drive Shaft inside the Differential to stop them rattlingto fit:Classic Fiat 500 all modelsFiat 126 all modelsIf you have any questions please contact us for help..

Polished Chrome Front Grease Cap fits on the Front Hub and acts as a dust & dirt shieldDiameter 34.5mmto fit:Classic Fiat 500 all modelsFiat 126 early models (594cc)If you have any questions please contact us for help..

Polished Chrome Front Grease Cap fits on the Front Hub and acts as a dust & dirt shield Diameter 47mmFiat Part No: 814635,4410279to fit:Classic Fiat 500 GiardinieraFiat 126 all models (650cc & 704cc)Fiat 600 all modelsFiat 850 all modelsFiat 124 all models ..

Rear Hub Shaftto fit:Classic Fiat 500 F/L & R all models  (from 1966 to 1974)Fiat 126 early model with 190 PCD Wheels  (up to 1977)If you have any questions or queries please contact our office for help..

Brand Newto fit:Classic Fiat 500 GiardinieraFiat 600 Series 2 all modelsFiat 126 all modelsIf you have any questions please contact us for help..

Rear Hub Flange (4 bolt type)(for 22mm Drive Shaft)to fit:Classic Fiat 500 F/L & R all models  (from 1966 to 1974)Fiat 126 all modelsFiat 600If you have any questions or queries please contact our office for help..

Rear Hub Flange (4 bolt type) Fiat Part No: 4144477 to fit:Fiat 850 all modelsFiat 850T & 900 T/E If you have any questions or queries please contact our office for help..

Rear Hub Nutto fit:Classic Fiat 500 all models  (up to 1974)Fiat 126 all models (up to 1999)Fiat 600Fiat 850If you have any questions or queries please contact our office for help..

Brand New Boxed PartsSupplied complete with1x  Rear Hub Carrier1x  Rear Wheel Bearing Kit inc Nut And Spacerto fit:Classic Fiat 500 all modelsFiat 126 all modelsIf you have any questions please contact us for help ..

These Stub Axles are fully factory reconditioned in Italy using Brass Bushes to last much longerThey have new top Bushes, Pins, Washers and Bushes and are ready to fit.The Kit also comes with two new Hub Nuts(Once fitted they must be greased fully using a grease gun until the g..

The benefit of these tie straps over plastic ones is that they are made from non corrosive stainless steel They are mainly designed to be fitted to CV Boots which are under constant threat from water, heat and road grime..

Made in ItalyComplete Kit For Both SidesThis is an uprated CV Style Joint that would replace the existing Aluminium Coupling which is a common weak point of the drive trainPerfect for standard cars but also cars with tuned engines adding more stress to the drive shaft & joints ..

This great kit replaces the Aluminium Coupling on the Drive Shaft at the wheel end and replaces it with a more robust and modern CV Joint with Tripod bearing. A must do job if you have a non standard car or engine with more power, as it eliminates a definite weak point in the driveThis grea..