Gaskets, Seals, Grommets and Rubber Parts

To fit over the Accelerator/Throttle Pedal to add gripto fit:Classic Fiat 500 all models (up to 1974)Fiat 126 all  modelsFiat 600 all modelsIf you have any queries or questions please feel free to ask..

This is a complete kit including1x Bonnet Seal Grommet Kit (fits around the aperture of the front Bonnet Seal to make the opening and closingsmoother and keep the gaps consistent1x Rear Engine Lid Grommet Kit (two fit on either side of the engine lid onto the body so the lid closes and d..

Quality Rubber Made in ItalyThis rubber pad or grommet fits around the Bonnet and rear Engine Lid aperture to fit:Classic Fiat 500 all models..

This kit fits around the aperture of the front Bonnet Seal to make the opening and closingsmoother and keep the gaps consistentto fit:Classic Fiat 500 all modelsIf you have any questions or queries please feel free to ask..

This rubber cone shaped grommet fits onto the front panel and the bonnet closes down onto itIt is also used on the sunroof to stop the handle Length of Cone: 19mmDiameter of base: 19mm  to fit:Classic Fiat 500 all modelsFiat 126, Fiat 600, 1100 all ..

Genuine Fiat PartsThis is a rubber pedal shaped cover for the Brake and Clutch Pedal to add gripto fit:Classic Fiat 500 all models (up to 1974)Fiat 126 all  modelsFiat 850 Special & various modelsIf you have any queries or questions please feel free to ask..

Rubber Seal/Gasket to fit between the Bumper Bracket and the bodyworkand prevent any marks or damageto fit:Classic Fiat 500 all modelsFiat 126Fiat 600If you have any queries or questions please feel free to ask..

This is a set of FOUR Rubber Seal/Gasket to fit between the Bumper Bracket and the bodyworkand prevent any marks or damageto fit:Classic Fiat 500 all modelsFiat 126Fiat 600If you have any queries or questions please feel free to ask..

Brand NewMade in ItalySupplied as a set of FOUR (4) Rubber Spacers to fit the Front & Rear Bumpersto fit:Classic Fiat 500 all models (except Giardiniera)Fiat 600 all modelsIf you have any questions please contact us for help ..

Made in ItalyThis kit includes the following,1x  Butterflyall x Gaskets (top,middle & bottom)1x Filter1x Needle Valve1x Copper Washer1x Metal WasherTo fit WEBER 28 ICP Carburettorto fit:Classic Fiat 600  767cc (1966 on)If you have any q..

Made in ItalyThis is a Black Plastic Plug that fits into the hole where the check strap bolt fits intoto fit:Classic Fiat 500 F/L/R all modelsIf you have any questions please contact us for help..

Brand NewMade in Italyto fit:Fiat 600D all modelsFiat 600 Multipla all modelsIf you have an questions please contact us for help..

This is a rubber plug or a 19mm hole on the dashboardto fit:Classic Fiat 500Fiat 126Fiat 600Fiat 850Fiat 124Autobianchi Bianchina..

This is a kit of2x Metal Support Plate 38mmx15mm x hole centre to centre 22mm4x Stainless Steel ScrewThese plates are used to fix either end of the rubber or canvas check strap to the car and door andgive it added support and a firm fixingto fit:Classic Fiat 500 a..

This rubber pad or grommet fits around the Door aperture on the top and bottomThere are TWO per Doorto fit:Classic Fiat 500 all models..

Good Quality Seals as OriginalMade in ItalyThis is a Roll of Rubber Door Seal to fit the two doors of a classic Fiat 600Dto fit:Fiat 600D all models from 1965 on (NOT Suicide Door Models)If you have any questions please contact us for help..

This is for ONE (1) metre of Rubber Channel thats fitted around the door opening glassThis is usually fitted inside the aperture of the door around the door glass, and stays in place due to the flexible spine that into the gapSize 14.5mm x 13mmto fit:Classic Fiat 500 all models ..

This is a 20 metre Roll Rubber & Metal ChannelAs you can see from the additional photos it should fit along the top edge of the door and down the back, and the door glass will move up and down inside it13mmx14.5mmto fit:Classic Fiat 500 all models (up to 1974)Fiat 126 a..

This Rubber & Metal Channel is measured for ONE Door to fit along the top and down the rear of the door glass and into the doorAs you can see from the additional photos it should fit along the top edge of the door and down the back, and the door glass will move up and down inside itFiat..

This Seal fits on the bulkhead between the engine and gearbox (see diagram)to fit:Fiat 600D all modelsIf you have any questions please contact us for help..